Dry Carbon Fiber Window Lift Button Trim & Switch Covers for Tesla Model Y L
-
$149 이상 주문 시 무료 배송
-
30일 무료 반품 및 교환
-
30일 가격 보호
-
평생 고객 지원
문의하기
Dry Carbon Fiber Window Lift Button Trim & Switch Covers for Tesla Model Y L
Real dry carbon fiber on the panel your fingers find first.
A ten-piece dry carbon fiber overlay set for the window lift button panels and door switch buttons on all four doors of the Tesla Model Y L. The factory switches, backlighting, and button travel stay exactly as they are. Only the surface changes.
Replaces the factory piano-black gloss
The window switch panel is the highest-contact surface on an interior door, and it shows every fingerprint and fingernail mark. Woven carbon breaks up that flat gloss black without touching the button layout or the backlight.
Dry carbon, not a printed pattern
Carbon fiber prepreg is molded and cured under heat and pressure, so the weave is part of the structure rather than a film printed on plastic. The twill carries real depth and direction as light moves across it.
Peel, press, done — and reversible
Every cover arrives with 3M double-sided adhesive already applied to the reverse side, plus an adhesion promoter wipe. No door panel removal, no drilling, and the original trim stays complete underneath if you ever want it back.
Ten pieces. Four doors. One weave direction.
A closer look at the details.
Material Construction
Carbon fiber prepreg — 2x2 twill carbon fabric pre-impregnated with epoxy resin — molded into a thin overlay shell. Because the layers are laid by hand into a closed mold, the twill runs in one consistent direction across every piece in the set.
Manufacturing Process
Prepreg is laid into the mold, then compression molded and cured under heat and pressure. Each piece is trimmed, sanded, and finished with a gloss clear coat before the 3M double-sided adhesive is applied to the reverse side.
Surface Finish
2x2 twill weave under a high-gloss, UV-stabilized clear coat. The gloss deepens the weave pattern and reads closest to the factory piano-black it replaces, which is why it is the finish shown throughout this page.
Flush edge and OEM-fit radius
Each cover is trimmed to a soft, OEM-fit radius where it meets the door panel and the button openings. There is no hard lip for a sleeve, a ring, or a cleaning cloth to catch on, and the cover sits flush with the surrounding trim rather than proud of it.
The reverse side carries die-cut 3M double-sided adhesive, protected by a red release liner until you are ready to press the cover down. The supplied adhesion promoter wipe matters most along the edges and on low-surface-energy areas — that is what keeps the perimeter flat through summer heat cycles.
View test results and conditions
Pending. Add test type, applicable SKU, result, comparison baseline, conditions, and evidence source once product-specific testing is available.
Check compatibility before ordering.
| Compatible Models | Tesla Model Y L (six-seat long-wheelbase Model Y) |
|---|---|
| Version / Production Range | Model Y L, from launch in August 2025 onward, including vehicles built at Giga Shanghai and, from July 2026, Giga Texas. |
| Not Compatible With | Tesla Model Y (2020–2024), including early 2025 production. Tesla Model 3 (2017–2023) and Model 3 Highland rear doors. Right-hand-drive vehicles — this set is molded for left-hand drive. |
| Clearance Requirements | Adds approximately 1 mm of thickness over the factory panel. No contact with the switch, the door pull, or the window glass; window travel, door release, and the child lock are unaffected. |
How do I identify my vehicle version?
Three checks in order. First, confirm the seating layout: the Model Y L is the six-seat, three-row version with two individual second-row seats, so a five-seat Model Y is not the same vehicle and this set will not fit. Second, check the production date on the driver-side B-pillar label or in the vehicle software information screen — this set covers Model Y L from its August 2025 launch. Third, compare the passenger door window switch panel: on the 2020–2024 Model Y that panel is dimensionally different from the newer layout. If you would rather not guess, send a photo of your door switch panel and your vehicle information screen to support@tesery.com before ordering and we will confirm.
Know what to prepare before installation.
Peel-and-press installation, roughly 15 minutes for all four doors.
- Mounting method: pre-applied 3M double-sided adhesive, with adhesion promoter supplied for the panel edges.
- Removal or drilling: none. No door panel removal, no drilling, and no modification to the factory trim.
- Recommended installer: DIY. The only skill involved is lining up the button openings before the tape touches the panel.
- After installation: keep the doors dry for the first 24 hours and avoid frequent window cycles while the adhesive sets. In cold weather, extend this to 72 hours.
Included in the Box
- Window lift switch panel trim covers × 4 — one for each door
- Door release and lock button covers × 6
- 3M double-sided adhesive, pre-applied to the reverse side of every cover
- Adhesion promoter wipe
Prepare Separately
- Clean microfiber cloth — one for cleaning, one for pressing
- Plastic trim tool and a hair dryer or heat gun, for removal only
- Adhesive remover, for cleaning residual tape if you later take the covers off
- 01Park the vehicle, switch off, and close the windows. Wipe each panel with the promoter wipe and let it flash off completely — dust and hand oil are what cause lifting edges. Then dry-fit every cover with the liner still on, starting at the driver door, and check the button openings and the weave direction against the other doors.
- 02Peel one corner of the red liner and hold that corner while you seat the opposite edge first. Press outward from the middle to push air ahead of the tape, working toward the open corner as you peel. Press firmly for 30 to 60 seconds, concentrating on the edges and the openings around each button.
- 03Check every edge for lift, trapped air, or obstruction of the switch, and confirm the backlight is still fully visible. Test the window travel and the door release, then press the whole set down once more. Keep the doors dry and out of direct sun for 24 hours.
A few more things to know.
Fitment help, warranty claims, and order support: support@tesery.com. Covered by a 30-day warranty against manufacturing defects.
How should I clean and care for this part?
Mild soap and water, applied with a soft microfiber cloth, is all this surface needs. Wipe, then dry immediately rather than letting water sit along the edges. Wax or a ceramic coating every two to three months keeps the clear coat working against UV.
Avoid alcohol, tar remover, solvent-based dressings, abrasive polish, and stiff brushes. Never scrub a dry panel with a dry cloth — that is what leaves fine scratches in a clear coat. Fingerprints show more on the gloss finish than they would on a matte one, and they wipe straight off. Long-term parking in direct sunlight will eventually dull or slightly yellow any carbon fiber clear coat, so a shaded spot or a UV protectant slows that down considerably.
Can the vehicle be returned to its original condition?
Yes. Warm the cover gently with a hair dryer on low, work a plastic trim tool or a length of fishing line under an edge, and lift slowly. Clean any residue with adhesive remover. Because nothing was cut or drilled, the factory panel underneath is untouched.
The adhesive itself is single-use: once removed, a cover needs fresh 3M tape before it can go back on. We do not describe these covers as re-usable without replacement tape.
Will it work with other aftermarket accessories?
These covers are designed to sit flush within the existing door panel, so they do not interfere with window travel, door release, or the child lock, and there is nothing else mounted on that surface to conflict with.
For the closest visual match, pair them with other TESERY dry carbon interior parts in the same finish. Weave direction and gloss level vary between suppliers, so mixing brands side by side in one cabin is the one combination we cannot guarantee.
What if the part does not fit or arrives damaged?
Contact support@tesery.com and include your order number, your vehicle model and production year, photos of the condition issue, and photos of the outer box and shipping label. Please check fitment against the panel before you remove the adhesive liner — once the liner is off, the covers cannot be resold as new, which affects whether a return can be accepted.
Every order is covered by a 30-day warranty against manufacturing defects such as delamination or a clear coat fault. Full return and refund conditions, including who covers return shipping, are set out in our refund policy.
중요 안내:
설치 후 문제가 발생하면 제품을 제거하기 전에 반드시 저희에게 연락해 주세요.
차량 정보(모델/연식/VIN)와 사진 또는 짧은 동영상을 함께 제공해 주시면 문제 해결이 훨씬 빨라집니다.
문제 해결 전에 제품을 제거하거나 변경한 경우 반품 또는 교환이 어려울 수 있습니다.
TESERY 반품 정책
걱정 없이 즐거운 쇼핑 경험을 제공하기 위해 최선을 다하고 있습니다. 상품을 반품해야 하는 경우 명확하고 편리한 반품 서비스를 제공합니다.
1. 주문 취소
-
배송되기 전에는 주문 취소를 요청할 수 있습니다.
-
주문이 이미 배송된 경우 배송을 중지하기 위해 최선을 다하지만, 성공을 보장할 수는 없습니다.
-
이메일 또는 온라인 고객 서비스를 통해 주문 취소 요청을 제출해 주세요.
2. 30일 반품 정책
상품을 받은 날로부터 30일 이내에 반품을 요청할 권리가 있습니다. 원활한 처리를 위해 이 30일 기간 내에 문의하고 반품을 신청해 주세요.
3. 반품 자격 요건
환불을 받으려면 반품 상품이 다음 조건을 충족해야 합니다.
-
상품은 미착용, 미사용 상태로 태그가 부착되어 있으며 원래 포장 상태를 유지하는 등, 수령 당시와 동일한 상태여야 합니다.
-
구매 증빙이 필요합니다.
4. 반품 사유 및 관련 수수료
반품에는 두 가지 유형이 있습니다.
-
품질 문제 또는 상품 손상:
-
받으신 상품에 결함이 있거나 손상되었거나 잘못된 상품을 받으신 경우 즉시 문의해 주세요. 전액 환불 또는 교환품을 제공해 드리며, 관련 비용은 모두 당사가 부담합니다.
-
-
품질과 무관한 반품(예: 개인적인 선호):
-
개인적인 선호(예: 단순 변심, 색상 또는 스타일 불만족)로 반품을 신청하는 경우 15% 재입고 수수료가 부과되며, 반품 배송비는 고객님이 부담하셔야 합니다.
-
5. 반품 절차
반품을 시작하려면 다음 단계를 따르세요.
-
문의하기:
-
다음 주소로 이메일을 보내세요
support@tesery.com/ service@tesery.com 또는 실시간 채팅을 이용해 반품 요청을 알려 주세요.
-
-
안내 받기:
-
반품 요청이 승인되면 배송 주소와 포장 지침을 포함한 자세한 반품 안내를 보내드립니다.
-
-
상품 반송:
-
제공된 안내에 따라 상품을 반송해 주세요. 반품 요청을 먼저 하지 않고 당사로 보낸 상품은 접수되지 않는다는 점에 유의해 주세요.
-
6. 반품 불가 상품
제품의 특성상 일부 상품은 반품할 수 없습니다:
-
맞춤 제작 제품: 예를 들어 맞춤 제작 제품으로 명시된 스티어링 휠과 휠은 품질과 관련 없는 문제로는 반품할 수 없습니다.
-
특정 상품: 기프트 카드, 위험 물질 또는 인화성 액체/가스가 포함됩니다.
특정 상품의 반품 가능 여부에 대해 궁금한 점이 있으면 구매 전에 문의해 주세요.
7. 환불 및 교환
-
환불:
-
반품하신 상품을 수령하고 검수한 후, 환불 승인 여부를 알려 드립니다. 승인된 환불은 영업일 기준 1~5일 이내에 원래 결제 수단으로 자동 처리됩니다. 최종적으로 금액이 입금되는 시점은 이용하시는 은행 또는 신용카드 회사에 따라 다릅니다.
-
-
교환:
-
원하는 상품을 가장 빠르게 받으려면 현재 보유한 상품을 반품하고, 반품이 승인된 후 새 상품을 별도로 구매하시기를 권장합니다.
-
8. 애프터서비스 지원 요건
공정하고 효율적인 해결 절차를 위해 고객은 애프터서비스 지원을 요청할 때 필요한 정보를 제공해야 하며, 여기에는 다음이 포함되지만 이에 국한되지 않습니다:
- 차량 정보(모델, 연식, VIN)
- 문제에 대한 명확한 설명
- 문제를 보여 주는 관련 사진 및/또는 짧은 동영상
참고:
필수 정보를 제공하지 않으면 문제를 정확하게 진단하지 못할 수 있으며, 반품, 환불 또는 교환 처리가 지연되거나 불가능할 수 있습니다.
사전 연락 없이 설치, 개조 또는 제거된 제품의 경우, 제품 상태를 확인할 수 없으면 TESERY는 반품 요청을 거부할 권리를 보유합니다.
